源地址：/mchina/archive//08/27/2644391.html
一、简介
VS/NAT原理图：
二、系统环境
实验拓扑：
系统平台：CentOS 6.3
Kernel：2.6.32-279.el6.i686
LVS版本：ipvsadm-1.26
keepalived版本：keepalived-1.2.4
三、安装
0、安装LVS前系统需要安装popt-static，kernel-devel，make，gcc，openssl-devel，lftp，libnl*，popt*
1、在两台Director Server上分别配置LVS+Keepalived
LVS install -------------
[root@CentOS-LVS_MASTER ~]# wget /software/kernel-2.6/ipvsadm-1.26.tar.gz
[root@CentOS-LVS_MASTER ~]# ln -s /usr/src/kernels/2.6.32-279.el6.i686//usr/src/linux/
[root@CentOS-LVS_MASTER ~]# tar zxvf ipvsadm-1.26.tar.gz
[root@CentOS-LVS_MASTER ~]# cd ipvsadm-1.26
[root@CentOS-LVS_MASTER ipvsadm-1.26]# make && make install
Keepalived install -------------
[root@CentOS-LVS_MASTER ~]# wget /software/keepalived-1.2.4.tar.gz
[root@CentOS-LVS_MASTER ~]# tar zxvf keepalived-1.2.4.tar.gz
[root@CentOS-LVS_MASTER ~]# cd keepalived-1.2.4
[root@CentOS-LVS_MASTER keepalived-1.2.4]# ./configure && make && make install
#########将keepalived做成启动服务，方便管理##########
[root@CentOS-LVS_MASTER ~]# cp /usr/local/etc/rc.d/init.d/keepalived /etc/init.d/
[root@CentOS-LVS_MASTER ~]# cp /usr/local/etc/sysconfig/keepalived /etc/sysconfig/
[root@CentOS-LVS_MASTER ~]# mkdir /etc/keepalived/
[root@CentOS-LVS_MASTER ~]# cp /usr/local/etc/keepalived/keepalived.conf /etc/keepalived/
[root@CentOS-LVS_MASTER ~]# cp /usr/local/sbin/keepalived /usr/sbin/
[root@CentOS-LVS_MASTER ~]# service keepalived start | stop
2、开启路由转发
[root@CentOS-LVS_MASTER ~]# vim /etc/sysctl.conf
net.ipv4.ip_forward = 1
[root@CentOS-LVS_MASTER ~]# sysctl -p
3、配置Keepalived
[root@CentOS-LVS_MASTER ~]# less /etc/keepalived/keepalived.conf
! Configuration File for keepalivedglobal_defs {router_id LVS_MASTER #BACKUP上修改为LVS_BACKUP}vrrp_instance VI_1 {state MASTER #BACKUP上修改为BACKUPinterface eth0virtual_router_id 51priority 100 #BACKUP上修改为80advert_int 1authentication {auth_type PASSauth_pass 1111}virtual_ipaddress {10.0.0.227}}vrrp_instance LAN_GATEWAY {state MASTER #BACKUP上修改为LVS_BACKUPinterface eth1virtual_router_id 52priority 100 #BACKUP上修改为80advert_int 1authentication {auth_type PASSauth_pass 1111}virtual_ipaddress {192.168.10.10}}virtual_server 10.0.0.227 80 {delay_loop 6lb_algo rrlb_kind NAT# persistence_timeout 5protocol TCPreal_server 192.168.10.4 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}real_server 192.168.10.5 80 {weight 3TCP_CHECK {connect_timeout 3nb_get_retry 3delay_before_retry 3connect_port 80}}}
BACKUP服务器同上配置，先安装lvs再安装keepalived，然后配置/etc/keepalived/keepalived.conf，只需将批注部分改一下即可。
4、分别在2台Real Server上面设置网关
把网关都设置成：192.168.10.10
5、在2台RealServer中分别配置HTTP
[root@WEB1 ~]# yum -y install httpd
[root@WEB1 ~]# cd /var/www/html/
[root@WEB1 html]# cat index.html
<h1>WEB1/192.168.10.4</h1>
[root@WEB1 html]# /etc/init.d/httpd start
另一台机器配置一样，过程略。
6、分别在CentOS-LVS_MASTER、CentOS-LVS_BACKUP上执行service keepalived start启动keepalived就可实现负载均衡及高可用集群了；
[root@CentOS-LVS_MASTER keepalived]# service keepalived start
四、测试
####高可用性测试####
模拟故障，将CentOS-LVS_MASTER上的keepalived服务停掉，然后观察CentOS-LVS_BACKUP上的日志，信息如下
从日志中可知，主机出现故障后，备机立刻检测到，此时备机变为MASTER角色，并且接管了主机的虚拟IP资源，最后将虚拟IP绑定在etho设备上。
将CentOS-LVS_MASTER上的keepalived服务开启后，CentOS-LVS_BACKUP的日志状态。
从日志可知，备机在检测到主机重新恢复正常后，释放了虚拟IP资源重新成为BACKUP角色
####故障切换测试####
故障切换是测试当某个节点出现故障后，Keepalived监制模块是否能及时发现然后屏蔽故障节点，同时将服务器转移到正常节点来执行。
将WEB2节点服务停掉，假设这个节点出现故障，然后主、备机日志信息如下
从以上可以看出，Keepalived监控模块检测到192.168.10.5这台主机出现故障后，将WEB2从集群系统中剔除掉了。此时访问http://10.0.0.227只能看到WEB1了)
重新启动WEB2节点的服务，日志信息如下：
Keepalived监控模块检测到192.168.10.5这台主机恢复正常后，又将此节点加入集群系统中，再次访问就可以访问到WEB2页面了）
RHEL 5.4下部署LVS(DR)+keepalived实现高性能高可用负载均衡
/mchina/archive//05/23/2514728.html
