电弧焊,arc welding
1)arc welding电弧焊
1.Numerical model of thermal cycle inarc welding of steel plate and sheet;中厚、薄板快速电弧焊热循环数学模型
2.Environmental load assessment ofarc welding process;电弧焊过程的环境负荷评价
3.An example of applyingarc welding in repair of kiln and grind mill;电弧焊在窑磨修理中的应用实例
英文短句/例句
1.Suitable for MMA, argon arc, arc gouging welding.可用于手工电弧焊、弧焊、弧气刨.
2.automatic submerged slag welding of rail钢轨自动埋弧电弧焊
3.narrow gap one-side automatic welding窄间隙单面自动电弧焊
4.low hydrogen type covered electrode低氢型涂料电弧焊条
5.metal-arc gas-shielded welding气保护金属极电弧焊
6.metal arc inert gas welding金属惰性气体电弧焊
7.metal inert gas arc welding (MIG)惰性气体金属电弧焊
8.co3 gas arc welding二氧化碳气体电弧焊
9.MMA (Manual Metal Arc)人工金属电弧焊接法
10.inert gas metal arc welding金属极惰性气体电弧焊
11.mixed gas arc welding混合气体保护电弧焊
12.inert-gas shielded arc welding惰性气体保护电弧焊法
13.GCAW (Gas Carbon-Arc Welding )气体保护碳极电弧焊
14.Arc Welding of Ti_3AlC_2 Ceramic to Cu AlloyTi_3AlC_2与Cu合金的电弧焊接
15.controlled tungsten-arc welding自动控制弧长的钨极电弧焊
16.magnetic flux gas shielded arc welding磁性焊剂气体保护电弧焊
17.low idle voltage arc-welding power supply低空载电压的弧焊电源
18.| wandering block sequence电弧飘移多层焊次序
相关短句/例句
electric arc welding电弧焊
3)arc welding电[弧]焊;弧焊
4)arc welding equipment电弧焊接;电弧焊
5)shielded metal arc welding焊条电弧焊
1.Discussion on safely using electricity inshielded metal arc welding process(3)——Measures to prevent electric shock accidents;焊条电弧焊用电安全问题的探讨(三)——防止触电事故的措施
2.Analysis on the Process and Cost of Shielded Metal Arc Welding and CO_2 Gas Shielded WeldingCO_2气体保护焊与焊条电弧焊工艺及成本分析
3.Single-pass and multi-passes welded joints of 0Cr18Ni9/20 clad pipe were prepared by the use ofshielded metal arc welding(SMAW) and E309L super-low carbon austenitic stainless steel electrode.采用E309L型超低碳奥氏体不锈钢焊条的焊条电弧焊(SMAW,shieldedmetal arc welding)方法制备了0Cr18Ni9/20复合管单层焊和多层焊接头,并应用光学金相、能谱(EDS,energy dispersive spectrum)成分及线扫描、扫描电镜(SEM,scanning electronmicroscope)、X射线衍射以及显微硬度等方法对焊接接头进行了对比分析研究。
6)welding rod arc welding焊条电弧焊
1.This article introduces the experiment that contrasted the welding joint"s performance and enameling capability among CO2 gas shielded welding,welding rod arc welding and submerged arc auto-welding, compares the welding cost between CO2 gas shielded welding andwelding rod arc welding, analyzes the feasibility of applying CO2 gas shielded welding on enamel glass equipment.本文对CO_2气体保护焊焊接接头与焊条电弧焊、埋弧自动焊焊接接头的性能、可涂搪性进行了对比试验,并对CO_2气体保护焊和焊条电弧焊两种焊接方法的焊接费用作了比较,进行了搪玻璃设备上应用CO_2气体保护捍的可行性分析。
延伸阅读
电弧焊电弧焊electric arc weldingd一onhUhon电弧焊(eleetrie ar。welding)利用电弧作为热源的熔焊方法，简称弧焊(见电坪、电弧加热)。焊接时，电弧在焊件的接缝处和电极之间燃烧，焊件接缝处的金属和必要时添加的坡充金属受热熔化，形成熔池;电极用手工或机械方法沿焊接方向移动，或电极固定，焊件移动;熔池冷凝后形成焊缝，把焊件连接在一起。电极分不熔化电极和熔化电极两种。不熔化电极通常用钨极，用以施焊时，可根据需要另加坡充金属。熔化电极在焊接时不仅传导电流，而且其端部不断熔化作为填充金属填在接缝中.熔化电极通常做成焊条和焊丝两种形式。前者多用于手工焊接，后者则多用于自动或半自动焊接。各种金属的焊接各有其适用的焊条或焊丝。电弧焊的主要种类和用途列于表。电弧焊有电弧温度高、热量集中且容易控制等特电筑娜的主要种类和用途┌─────────────┬─────────────────────────────┬───────┐│名称 │用途(适宜于焊接的材料和焊接厚度值)│适用的辉接位t │├─────────────┼─────────────────────────────┼───────┤│手弧焊│ 碳钢、合金钢、镶及镶合金、钥及钥合金等(3~20 mm)，铸铁│各种位l││ │(76 rn们。
