支模,supporting formwork
1)supporting formwork支模
1.The paper introduces multiple symmetrical pull-piece design and application in steel concrete wallsupporting formwork by engineering example,compares advantage and disadvantage with traditional pull-bolt and pull-bar.通过工程实例介绍了钢筋混凝土墙体支模中的复式对拉件设计及应用,并与传统的对拉螺栓和对拉条的优缺点进行了对比。
2.This paper introduces multiple symmetrical pull piece and its application insupporting formwork of concrete wall construction through a project example , compares its merits and demerits with traditional pull bar and pull bolt, and carries out designing and checking computation .通过工程实例介绍了复式对拉件及其在混凝土墙体支模中的应用 ,将其与传统的对拉螺栓和对拉条的优缺点进行了对比 ,结合实例对其进行了设计验算 ,实践表明对基础两侧地基松软和有抗渗要求的构筑物 ,混凝土墙体支模采用复式对拉件更为实用方便 ,效果好且不损坏模板 ,还提高了模板的周转
英文短句/例句
1.The structure of boards that make up a form for pouring concrete in construction.模板，支模，模壳用以放置混凝土的模板模壳
2.Design and Construction of High-Formwork and Large Span Formwork Supports System高支模、大跨度模板支撑体系的设计与施工
3.The Model Analysis about Millicent in Mcropayment Protocol;Millicent微支付协议中的支付模型分析
4.imitative or emulative consumption spending模仿或仿效的消费支出
5.Separate module from bracket.将模组与支架分离。
6.modular terminal support software package模块式终端支援软件包
7.Injection mould for plastic large-size mould bases-Support platesGB/T12555.5-1990塑料注射模大型模架支承板
8.is powered-up or reset). Color and Mono modes are supported. Primary适配器的模式)。支持彩色和单显模式。
9.Support files for "Spreadsheet Solutions" templates.“电子表格模板”中模板的支持文件。
10.Model Class Management And Organization in Modeling Support System建模支持系统中模型类的管理与组织
11.Enterprise Model and Modeling Methodology for Business Reengineering支持事务重建的企业模型与建模方法
12.A Model of Multiclass Pattern Recognition Based on Support Vector Machine;基于支持向量机的多类模式识别模型
13.Artillery Firepower Support in Vague Match Model Application炮兵火力支援中的模糊匹配模型应用
14.Decision support model of lump-sum contracting projects delivery methods UMADM总承包工程交易模式UMADM决策支持模型
15.Mixed Strategy Model of Fuzzy Payoff Matrix and Its Algorithm模糊支付矩阵混合策略模型及其求解
16.Improved Fuzzy Least Squares Support Vector Machines Model改进的模糊最小二乘支持向量机模型
17.A Study on Bank Card Payment Methods for Individuals;基于银行卡个人支付手段与支付模式的研究
18.Model test study of earth pressure on support structure支撑式支护结构上土压力的模型试验研究
相关短句/例句
form erecting支模
1.The paper introduces the construction method of using bolted fixture to improve theform erecting process in brick-and-concrete composite construction and this method has also produced an obvious result.文章介绍了砖混结构模板体系中应用螺栓夹具等改进的支模工艺的施工方法,并取得了明显的效果。
3)form erection支模
1.The practice shows that for the buildings the both sides of which s foundation are soft and have the requirement for impermeability, the duplex counter part, which should be adopted in the wallform erection, is practicable and convenient, its effect is good and doesn t damage the forms, and can increase the tur.通过工程实例介绍了复式对拉件设计及其在混凝土墙体支模中的应用,并与传统的对拉螺栓和对拉条的优缺点进行了对比。
4)model set technological支模工艺
1.This paper introduces the preloadingmodel set technological in heating furnace, preloadingmodel set technological can increase the quality of heating furnace and the life of furnace lining highly.在加热炉中采用预加载荷支模工艺,能提高加热炉施工质量,大大提高炉衬寿命。
5)fracture apparatus造模支架
1.Method A reformed simplifiedfracture apparatus was designed and tested on 78 male Sprague-Dawley rats.方法:简化设计并制作骨折造模支架。
6)help patterns支援模式
延伸阅读
木工支模拆模安全技术操作规程第1条 模板支撑不得使用腐朽、扭裂、劈裂的材料。顶撑要垂直，底端平整坚实，并加垫木。木楔要钉牢，并用横顺拉杆和剪刀撑拉牢。第2条 采用行架支模应严格检查，发现严重变形、螺栓松动等应及时修复。第3条 支模应按工序进行，模板没有固定前，不得进行下道工序。禁止利用拉杆、支撑攀登上下。第4条 支设4米以上的立柱模板，四周必须顶牢，操作时要搭设工作台，不足4米的，可使用马凳操作。第5条 支设独立梁、柱模应设临时工作台，不得站在柱模上操作和在梁启模上行走。第6条 拆除模板应经施工技术人员同意。操作时应按顺序分段进行，严禁猛撬、硬砸或大面积撬落和拉倒。工完前；不得留下松动和悬挂的模板，拆下的模板应及时运送到指定地点集中堆放。 第7条 拆除薄腹梁、吊车梁、行架等预制构件模板，应随拆随加顶撑支牢。
