提升机齿轮箱,elevator gearbox
1)elevator gearbox提升机齿轮箱
1.Study ofelevator gearbox fault diagnosis based on MATLAB and homomorphic demodulation基于MATLAB和同态解调的提升机齿轮箱故障诊断研究
英文短句/例句
1.Fault Diagnosis of Hoist Gearbox Based on EMD基于EMD的提升机齿轮箱故障诊断
2.Study of elevator gearbox fault diagnosis based on MATLAB and homomorphic demodulation基于MATLAB和同态解调的提升机齿轮箱故障诊断研究
3.Research of the Helicopter Gearbox Malfuction Diagnosis and Prediction Systemr直升机齿轮箱故障诊断及预测系统的研究
4.Research on Vibration Signal Processing Techniques and Applications to Fault Diagnosis of Helicopter Gearbox;振动信号处理技术在直升机齿轮箱故障诊断中的应用
5.change gear box交换齿轮箱，变速齿轮箱，挂轮箱
6.The rotary gear reducer is driven by a DC motor through a gearbox to pro-vide bi-directional drill bit rotation.转动齿轮减速器是由一个直流电机驱动的，通过一个齿轮箱为钻头提供双向转动能力。
7.The rate of the machine moved up sharply because of changing a big gear box.由于换了一个大齿轮箱这台机器的速度大大提高了。
8.Contact Finite Element Analysis of Hoister s Cracked Shaft Gear in Large Mining Excavator;大型矿用挖掘机提升机构含裂纹轴齿轮接触有限元分析
9.jacquard machine with double griffe blocks复式刀箱滑轮提花机
10.Fuel oil purifier overhauled and cleaned, gear case oil renewed.燃油分油机解体清洁，齿轮箱换油。
11.Viberation Test Analysis of Gear Box for Alloy Bar"s Rolling Mill合金棒材轧机的齿轮箱振动实测分析
12.Application of Self-lubrication Technology in Gearbox of Coal Mining Machine自动润滑技术在采煤机齿轮箱中应用
13.The analysis of fatigue for torsion shafts in the gearbox of wind turbine风力发电机齿轮箱扭力轴的疲劳分析
14.FAULT DIAGNOSIS SYSTEM OF GEAR BOX OF FINISHING MILL OF HIGH-SPEED WIRE LINE高速线材精轧机齿轮箱故障诊断系统
15.The Gearbox Fault Diagnosis Based on the Whole Machinery Vibration Spectrum Analysis基于整机运转状态的齿轮箱故障诊断
16.Influence of Gears in Helical Speed Increasing Box on Vibration of Blower Bush斜齿增速箱齿轮问题对风机轴瓦振动的影响
17.spur and helical hobbing machine正齿轮和斜齿轮滚齿机
18.Analysis and Research of Gear-Rotor System Dynamic in Wind Turbine Gearbox;风力发电机齿轮箱的齿轮转子系统动力学的分析与研究
相关短句/例句
helicopter gearbox直升机齿轮箱
1.In the end the proposed method is used to detect early bearing faults in onehelicopter gearbox and the results demonstrate that it is superior to power spectrum density (PSD) and demodulation an.最后在某型直升机齿轮箱轴承故障的早期检测中进行了实验验证。
3)retardation gear of hoisting machine提升机减速齿轮
4)elevating rick提升齿条齿轮
5)Gear case of wire rolling mills轧机齿轮箱
6)rotary elevator转轮提升机
延伸阅读
弧齿锥齿轮铣齿机用弧齿锥齿轮铣刀盘按展成法粗、精加工弧齿锥齿轮和准双曲面齿轮齿部的齿轮加工机床。弧齿锥齿轮铣齿机广泛用于机器制造业，尤在汽车、拖拉机工业中使用最多。加工直径小到10毫米，大至2500毫米。加工精度一般为7级(JB180-60)，有的可达6级。弧齿锥齿轮铣齿机（见图）的铣刀盘主轴装在偏心鼓轮内，用以调整铣刀盘中心的位置。偏心鼓轮装在摇台内，并随摇台(带着铣刀盘)作一定角度的摆动，与工件的相应角度的正反回转运动一起构成展成运动。摇台每上下摆动一次完成一个齿的切削，这时工件随床鞍退出，并进行分齿，然后床鞍又进到工作位置，切削第二个齿。全部齿切削完毕后机床自动停止。弧齿锥齿轮铣齿机的工件主轴箱可在立柱上作垂直位移的调整。当工件主轴与摇台中心等高时，可切削弧齿锥齿轮；偏移时可切削准双曲面齿轮；微量的偏移可用于调整轮齿的接触区。弧齿锥齿轮铣齿机的刀具主轴有水平固定安装的和可倾斜调整的两种。后者可减少?车杜痰钠分止娓窈屠┐蠡驳墓ひ湛赡苄裕滦突泊蠖嗖捎谜庵纸峁埂?弧齿锥齿轮铣齿机的变型很多，有结构简单、不带展成运动的粗切机，也有带展成运动的粗切机，还有专门精切大轮的拉齿机、专切大轮和兼切大、小轮的铣齿机等。
