热点应力幅,hot spot stress range
1)hot spot stress range热点应力幅
1.S-N curves based on thehot spot stress range are generally used to predict the fatigue life of tubular joints in offshore platformeering.对海洋平台中圆管节点的疲劳寿命估算,通常采用的是基于热点应力幅基础上的S-N曲线法。
2)hot spot stress热点应力
1.Key influence factors inhot spot stress FEM analysis;热点应力有限元分析的主要影响因素
2.Weld seam fatigue analysis of locomotive damper hold byhot spot stress method;机车减振器座焊缝疲劳的热点应力分析
3.Study of fatigue strength assessment of welds based onhot spot stress;基于热点应力的焊缝疲劳强度评定研究
英文短句/例句
1.Fatigue Strength Analysis of Bulk Carriers Based on Hot Spot Stress Method in CSR基于CSR中热点应力的散货船疲劳强度分析
2.Hot Spot Stress Concentration Factors of Diamond Bird-Beak SHS T-Joints钻石鸟嘴式方管T形节点热点应力集中系数分析
3.Hot Spot Stress Analysis of Steel Bridge Components and Numerical Simulation of Fatigue Damage Accumulation;桥梁构件局部热点应力分析及其疲劳损伤累积过程模拟
4.Research on Hot Spot Stress Evaluation Approach of Welded Bogie Frame on High-speed Trainset;高速客车转向架焊接构架热点应力评定方法的研究
5.Fatigue Life Study on Key Parts of Bogie Frame by Hot Spot Stress Method;基于热点应力法的转向架关键部件疲劳寿命研究
6.Analysis and Comparison of Thermal Stress and Hygrothermal Stress of Lead-free Flip Chip Solder Joint无铅倒装焊点的热应力与湿热应力分析
7.The Heat-transfer & Structure Characteristics of Dimple-jacket Applied in Pressure Vessel蜂窝夹套传热和结构特点在压力容器中的应用
8.Respond Actively to Social Focus and Enhance the Attraction of "Two-curricula" Teaching;积极回应社会热点 增强“两课”教学吸引力
9.Temperature Field Simulation and Thermal-Stress Analysis of Al Alloy Pressure diecasting Die铝合金压铸模具温度场模拟与节点热应力分析
10.Calculation Analysis of Thermal Stress of Propellant Grain in Ignition Process点传火过程中火药颗粒热应力的计算分析
11.A classification of thermo-hydraulic models adoptable under different conditions is presented in this context and the relevant similarity criteria as well as their permissible relaxation are given.据此观点提出了水力热力模型的分类和相应相似准则。
12.From the thermodynamics and the theory of heat, the mechanism of laser bending was expounded and the stress model in the process was built.从热学及热力学的观点出发,阐明了该工艺的变形机理,建立了弯曲过程中的应力模型;
13.Nothing less than a fission bomb can ignite a thermonuclear reaction.威力比一个裂变炸弹小的任何东西都不能点燃热核反应。
14.Steam is formed if the boiling point pressure for the temperature of the reservoir is reached.如果达到对应于热储温度的沸点压力,就会形成蒸气。
15.Employee"s Coping in the Workplace--Conceptions,Models,Measures and Issues工作环境下的员工压力应对研究——内涵、模型、测量及热点评述
16.nitrate cracking热硝酸盐应力腐蚀开裂
17.Mechanism and thermodynamics of carbothermal reduction of alumina氧化铝碳热还原反应机制及其热力学
18.Thermodynamic Analysis and Application of Convective Heat Transfer;对流换热过程的热力学分析及其应用
相关短句/例句
hot spot stress热点应力
1.Key influence factors inhot spot stress FEM analysis;热点应力有限元分析的主要影响因素
2.Weld seam fatigue analysis of locomotive damper hold byhot spot stress method;机车减振器座焊缝疲劳的热点应力分析
3.Study of fatigue strength assessment of welds based onhot spot stress;基于热点应力的焊缝疲劳强度评定研究
3)hot spot stress approach热点应力法
1.The midship region cargo was modeled with shell and beam elements and a fatigue assessment was carried out with applying thehot spot stress approach as following the instructions of Common Structural Rules for Oil Tankers(JTP).基于共同规范(JTP)的相关规定,针对某油轮建立三舱段有限元模型,采用热点应力法对内底和边舱斜板之间折角处进行了疲劳评估。
4)hot spot stress method热点应力法
1.According to the Guide for Building and Classing Membrane Tank LNG Vessels of ABS,the finite element model had been built and the fatigue strength assessment of a LNG vessel had been carried out with nominal stress method andhot spot stress method based on the fatigue accumulating damage concept of S-N curve approach.以某LNG船为研究对象,建立三舱段有限元模型,并根据美国船级社薄膜型LNG船体结构疲劳强度指南,基于S-N曲线法的疲劳积累损伤原理,分别采用名义应力和热点应力法,对船体典型节点进行疲劳强度评估,同时对计算结果进行分析;讨论低温下材料性能改变对节点疲劳寿命评估的影响。
5)hot spot stress areas热点应力区
1.The stress distribution of tubular T-joints athot spot stress areas and its maximum stress concentration factors(SCFs)under the axial loads are analyzed by use of finite element method.用有限元方法分析了承受轴向拉力作用时T型管节点在热点应力区的应力分布,以及最大应力集中系数,通过计算发现,最大应力集中系数出现在鞍点处。
6)SPATE(stess pattern analysis through thermal emissions)热幅射应力模型分析
延伸阅读
轧辊残余应力(见轧辊应力)轧辊残余应力(见轧辊应力)residual stresses in rollzhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。