充型速度,Filling Velocity
1)Filling Velocity充型速度
1.The Influence of Various Process Parameters on the Liquid MetalFilling Velocity in Gray Iron Casting Produced by EPC V Process;铸铁件EPC-V法工艺因素对充型速度的影响
2.The result indicats that there are few blowholes,inclusions except misrun in the casting with the filling velocity of 25mm/s,and the casting was formed with some blowholes、inclusions with the filling velocity of 40mm/s,while the casting was form.研究了薄壁铝合金铸件真空吸铸充型速度对其内部质量的影响,对一种200mm×180mm,壁厚为2。
3.The metal filling velocity increases with the reduction of pattern density and coating thickness, and the increase of pouring temperature.研究了模样密度、涂层厚度、浇注温度、真空度等工艺参数对可控气压下镁合金消失模铸造时液态金属的充填形态和充型速度的影响,以及充型速度与充型形态之间的关系。
英文短句/例句
1.Influence of Process Factors on Mould-Filling Velocity of Evaporated Pattern Casting(EPC)工艺因素对铸铁件消失模充型速度的影响
2.Filling Velocity of Metal Liguid,Mass and Energy Balances in EPC Process金属液在消失模铸造中的充型速度及能量和质量平衡
3.A Novel High-Speed High-Accuracy CMOS Precharge Comparator新型高速高精度CMOS预充电比较器
4.fully developed velocity distribution充分发展的速度分布
5.mean fully developed braking deceleration MFDD充分发出的平均减速度
6.The Surface Fluid Field Is Compared to Inside Fluid Field for Casting Filling Water Simulation Process铸造充型水模拟过程表面及内部速度场的对比分析
7.In extreme temperatures, the inflation rate will decrease a little bit.在极限温度中，充气速度会有一点降低。
8.NEW FAST CHARGING SYSTEM CONTROLLED BY BATTERY CHARGING CURRENT ACCEPTANCE一种新型快速充电体制的研究:以充电电流接受力控制的充电
9.From there the air fills up the room at very low speed.新风以非常低的速度充满整个房间。
10.She must turn to full account her speed to win a medal.她必须充分利用她的速度赢得奖牌。
11.She must make a full use of her speed to win a medal.她必须充分利用她的速度来赢得奖牌。
12.At some banks, capital ratios are dropping fast.一些银行的资本充足率下降速度很快。
13.Design of An Intelligent Automatic Rapid Charger一种智能型全自动快速充电机的设计
14.Simulation of the Multiple Velocity and Acceleration Difference Model加速度差与多速度差模型的数值模拟
15.Numerical simulation for velocity and pressure in filling stage of injection molded parts with uneven thickness注塑充填过程变厚度截面速度压力场数值模拟
16.interferometric fiber optic accelerometer干涉型光纤加速度计
17.speed test cassette速度测试卡型盒式磁带
18.a well-publicized attempt to break the world speed record为打破世界速度纪录的尝试进行了充分的宣传.
相关短句/例句
mold filling velocity充型速度
1.Study onmold filling velocity in AZ91 magnesium alloy LFC process with vacuum;AZ91镁合金负压消失模铸造充型速度的研究
2.The influence of processing parameters on themold filling velocity during investiment casting was investigated by using an integrated system of experimental equipment and a specially designed computer data acquisition device.用消失模铸造试验装置和计算机数据采集系统研究了工艺因素对充型速度影响的规律。
3.Themold filling velocity of AI alloy melt in lost foam casting process was investigated by X-ray technology and other method.充型中期,充型速度增加较快;而充型末期,由于温度降低以及气压升高,充型速度锐减。
3)filling speed充型速度
1.Thefilling speed of lost foam cast iron casting was measured by use of an integrated set of experimental equipment and a specially designed computer acquisition system.研究了负压度、模样密度、浇注温度、金属静压头等工艺因素对消失模铸铁件充型速度的影响规律。
4)velocity of high-speed injection stage快速充型速度
1.The results show that the surface quality of magnesium alloy die casting improved greatly with the increase of thevelocity of high-speed injection stage in a cert.针对汽车发动机缸盖罩盖零件,采用压力传感器,通过对铸件的表观质量进行评定及铸件密度和抗拉强度的测定,系统研究了镁合金压铸过程中快速充型速度和起速位置对型腔内压力变化和铸件质量的影响。
5)critical filling rate临界充型速度
1.It is shown that the wall width of castings has obvious effect on critical pressure increase rate andcritical filling rate, the thinner the wall width of castings is, the bigger the critical pressure increase rate andcritical filling rate .实验结果表明 ,铸件壁厚对临界加压速度和临界充型速度影响很大 ,铸件壁越薄 ,临界加压速度和临界充型速度也越大 ;内浇口形状和数量对充型平稳性影响不显著。
6)filling speed measurement充型速度测试
延伸阅读
充炭黑充油丁苯橡胶分子式：分子量：CAS号：性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
